REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 Phillips screwdriver and flat head screw driver 

Needle nose pliers

Note: Please read carefully before refilling cartridge.

General Refilling Procedures:

Using the screw driver, remove the screws on the side of the cartridge so that the toner plug can

be revealed. Once you have located the toner plug, use the flat head screw driver to gently loosen

the sealing plug. With the needle nose pliers, gently, but forcefully pull the plug completely off

the cartridge. If the plug happens to bent or crack, you may use electrical tape or duct tape to

securely seal the cracks or bents once you have replaced the plug at the end of the refill process.

Empty any toner left inside the cartridge (mixing two different brands of toner could result in bad

printing, and unpredictable results).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner

and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel

cap making to sure it is on tightly. Tilt the cartridge at a 45 degree angle and then the funnel cap

toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge

is full, simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.

Once you are done refilling this cartridge, place the sealing plug back in its place and use duct

tape or electrical tape to seal up any necessary cracks on the plug.

Replace the Smart Chip on the cartridge before placing it back into the printer. The chip may

need to be pried from its location gently. Once the chip has been replaced, insert the cartridge

into the printer and run a few test pages.

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the

cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before

refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best

results (if possible).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner

and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap

making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole.

If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn

the bottle upside down and tap it on a table. Once the cartridge is full, seal the hole with the plug

by twisting it until it is completely seated. Now gently shake the cartridge side to side to distribute

the toner.

Replace Chip

Remove the old chip. You may need to pry the old chip off using a flat head screwdriver. Once

the old chip has been removed replace it with the new chip. If the new chip does not have a

double back taping strip, use a dab of super glue to hold the hcip in place.

Install and test the cartridge by printing a few pages.

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 Phillips screwdriver and flat head screw driver

 Needle nose pliers

Note: Please read carefully before refilling cartridge.

General Refilling Procedures:

Using the screw driver, remove the screws on the side of the cartridge so that the

sealing plug can be revealed (Illustration A.). Once you have located the sealing

plug, use the flat head screw driver to gently loosen the sealing plug(Illustration

B..). With the needle nose pliers, gently, but forcefully pull the plug completely

off the cartridge. If the plug happens to bent or crack, you may use electrical

tape or duct tape to securely seal the cracks or bents once you have replaced the

plug at the end of the refill process.

Empty any toner left inside the cartridge (mixing two different brands of toner

could result in bad printing, or rare discoloration in your prints).

Before opening the bottle of toner, turn it upside down and tap it on a table to

loosen the toner and allow it to flow freely. Remove the cap and pull the seal off

the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the cartridge

at a 45 degree angle and then the funnel cap toward the filling hole and insert

it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a

table. Once you are done refilling this cartridge, place the sealing plug back in

its place and use duct tape or electrical tape to seal up any necessary cracks on

the plug.

Replace the fuse for this cartridge (Illustration B.. shows the fuse compartment).

Once you have replaced the fuse, you may now reinsert your cartridge back into

your printer and begin printing. Changing the fuse is only required for the Dell

1100 and Samsung 2010 cartridge.

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 Smart Chip

General Refilling Procedures:

1. Identify the filling hole on the side of the cartridge. There may be a sticker over the

filling cap that says “DO NOT REMOVE”. It is OK to remove this sticker. The

plastic sealing cap can be easily removed by prying it out with a flat screwdriver, but

be careful not to damage this plastic cap as you need to place it back after you refill

2. Now you can fill the cartridge with toner. Before opening the bottle of toner, turn

it upside down and tap it on a table to loosen the toner and allow it to flow freely.

Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure

it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If

the toner stops flowing before the cartridge is full, simply remove the toner, close the

cap, turn the bottle upside down and tap it on a table. Once the cartridge is full seal

the hole with the original plug.

Replacing the Smart Chip

3. Using a screwdriver, remove the 5 screws that are located on the TOP of the cartridge.

See picture A.

4. Carefully separate the two halves.

5. Locate the smart chip as shown in the image C, and replace it with a new replacement

chip

6. Now replace the cover of the cartridge and replace all 5 screws, making sure the

cover is securely attached.

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using. Position the copper bit on the cartridge in the spot indicated by the photograph and push gently until it melts a hole in the cartridge. Remove the tool, place it back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge or cause print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out. Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and allow it to flow freely. Remove the cap

and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually damage the photo-optic drum. Instead hold one end of the cartridge up off the table and twist the plug until it fully sealed. Now gently shake the cartridge side to side to distribute the toner.

Important: These cartridges have a chip that needs to be replaced in order for the printer to recognize the refilled cartridge. This chip is located on the side of the cartridge as shown in the picture. To access the chip, you need to unscrew three (3) screws on the end-cap of the cartridge around the chip. BE VERY CAREFUL when removing the end cap because there is a spring that could fall loose. You need to remove this spring in order for the cap to come off completely. Make sure you notice where the spring is do you can put it back the same way. Also BE VERY CAREFUL when removing the cap so that the gears on the inside of the end cap do not fall out, if they do you need to place them back. Once the cap has been removed, you will be able to remove the old chip. You have to now install a new compatible chip, making sure the contacts are positioned as in the diagram here. Carefully replace the end cap after you have installed the new chip.

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in photograph A

and push gently until it melts a hole in the cartridge. Make sure to keep the hole on the

flat surface of the cartridge and not on the curved edge. Remove the tool, place it back

on its stand and unplug it. If the small piece of plastic has fallen into the cartridge, it

must be removed, as this can damage your cartridge or cause print defects. If the piece

remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can, or use a vacuum

with a hose for best results (if possible). Do not overfill the cartridge by pouring the

entire toner powder into the cartridge. Use half the bottle now, and the rest at a later

time. Overfilling can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner. Replace the chip, and you are not ready to use the cartridge.

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 Smart Chip

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side

of the side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as

much as possible before refilling. If possible, use a vacuum to remove excess

toner from the cartridge, or use compress air to carefully and gently

blow out any toner inside the toner hopper (Please try to use compressed

air in a well ventilated area) for best results. Dispose of toner properly into

a trash can.

Before opening the bottle of toner, turn it upside down and tap it on a table to

loosen the toner and allow it to flow freely. Remove the cap and pull the seal

off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the

funnel cap toward the filling hole and insert it into the hole. If the toner stops

flowing before the cartridge is full, simply remove the toner, close the cap,

turn the bottle upside down and tap it on a table. Once the cartridge is full, seal

the hole with the plug by twisting it until it is completely seated. Now gently

shake the cartridge side to side to distribute the toner.

Remember to remove the old chip from the printer and place the new one

before installing the cartridge.

Canon - E16/E20/E31/E40

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool (Not Included, Sold Separately)

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Remove the tool, place it

back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,

it must be removed, as this can damage your cartridge or cause print defects. If the

piece remains in the tool, wait for the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner.

Canon - L50

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug (electrical or duct tape will do as well)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Remove the tool, place it

back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,

it must be removed, as this can damage your cartridge or cause print defects. If the

piece remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can, or use a vacuum

with a hose for best results (if possible).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug or electrical tape (Duct tape will do as

well).

Note: If there are gears that rotate near the refill hold created, do not use the plug,

instead use electrical tape or duct tape to seal the hole.

Gently rock the cartridge from side to side for about 5-10 seconds to distribute the

toner in the hopper. Your cartridge is now ready for use.

Canon – S35

Canon – X25

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool (Not Included, Sold Separately)

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Make sure to keep the

hole on the flat surface of the cartridge and not on the curved edge. Remove the tool,

place it back on its stand and unplug it. If the small piece of plastic has fallen into the

cartridge, it must be removed, as this can damage your cartridge or cause print defects.

If the piece remains in the tool, wait for the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner.

Canon – F100

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the tan portion of the cartridge on your right. Position the copper

bit on the cartridge in the spot indicated by the photograph and push gently until it

melts a hole in the cartridge. Remove the tool, place it back on its stand and unplug it.

If the small piece of plastic has fallen into the cartridge, it must be removed, as this can

damage your cartridge or cause print defects. If the piece remains in the tool, wait for

the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner

CANON A30, A15

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug (electrical or duct tape will do as well)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Remove the tool, place it

back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,

it must be removed, as this can damage your cartridge or cause print defects. If the

piece remains in the tool, wait for the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner.

CANON FX-8
CANON S-35

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 Duct Tape

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in the photograph and

push gently until it melts a hole in the cartridge. Make sure to keep the hole on the flat surface

of the cartridge and not on the curved edge. Remove the tool, place it back on its stand

and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed,

as this can damage your cartridge or cause print defects. If the piece remains in the tool,

wait for the tool to cool down and pry it out.

Create a hole on the opposite end where the waste toner is located. Empty the waste toner

as much as possible, then seal it with electrical tape or duct tape. Once you have sealed it

proceed to the next step.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and

insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove

the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge

is full seal the hole with the tape

Firmly secure the tape and then gently rock the cartridge from side to side to distribute the

new toner.

CANON FX-9/FX-10

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional - Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in photograph A and

push gently until it melts a hole in the cartridge. Remove the tool, place it back on its stand

and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed,

as this can damage your cartridge or cause print defects. If the piece remains in the tool,

wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible

before refilling. Dispose of toner properly into a trash can, or use a vacuum with a

hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner

powder into the cartridge. Use half the bottle now, and the rest at a later time. Overfilling

can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and

insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove

the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge

is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually damage

the photo-optic drum. Instead hold one end of the cartridge up off the table and twist

the plug until it fully sealed. Now gently shake the cartridge side to side to distribute the

toner.

CANON CARTRIDGE 106

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in photograph A

and push gently until it melts a hole in the cartridge. Make sure to keep the hole on the

flat surface of the cartridge and not on the curved edge. Remove the tool, place it back

on its stand and unplug it. If the small piece of plastic has fallen into the cartridge, it

must be removed, as this can damage your cartridge or cause print defects. If the piece

remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can . Do not overfill

the cartridge by pouring the entire toner powder into the cartridge. Use half or a

fourth of the bottle now, and the rest at a later time. Overfilling can and will damage

a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole properly.

Now gently shake the cartridge side to side to distribute the toner.

CANON CARTRIDGE 120

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using.

Position the copper bit on the cartridge in the spot indicated in photograph A and push gently until

it melts a hole in the cartridge. Make sure to keep the hole on the flat surface of the cartridge and not

on the curved edge. Remove the tool, place it back on its stand and unplug it. If the small piece of

plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge or cause

print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before

refilling. Dispose of toner properly into a trash can . Do not overfill the cartridge by pouring the

entire toner powder into the cartridge. Use half or a fourth of the bottle now, and the rest at a

later time. Overfilling can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and

allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making

to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the

toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle

upside down and tap it on a table. Once the cartridge is full seal the hole properly.

CANON CARTRIDGE 128
CANON IMAGECLASS MF4420

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using.

Position the copper bit on the cartridge in the spot indicated in photograph A and push gently

until it melts a hole in the cartridge. Make sure to keep the hole on the flat surface of the cartridge

and not on the curved edge. Remove the tool, place it back on its stand and unplug it. If the small

piece of plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge

or cause print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible

before refilling. Dispose of toner properly into a trash can . Do not overfill the cartridge by

pouring the entire toner powder into the cartridge. Use half or a fourth of the bottle now, and

the rest at a later time. Overfilling can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner

and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap

making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole.

If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn

the bottle upside down and tap it on a table. Once the cartridge is full seal the hole properly.

Brother – TN250

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

General Refilling Procedures:

Using your thumb, lift up the black plastic tab so that it unlocks from the cartridge

body. Rotate the entire black piece toward you. This will reveal a toner filling port.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full, twist the entire black plastic piece away from you until the tab

locks back in place.

Brother – TN350

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the

side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can, or use a vacuum

with a hose for best results (if possible).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen

the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.

Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling

hole and insert it into the hole. If the toner stops flowing before the cartridge is full,

simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.

Once the cartridge is full, seal the hole with the plug by twisting it until it is completely

seated. Now gently shake the cartridge side to side to distribute the toner.

Installing Reset Gear on Starter Cartridges

Using the illustration below as a guide, remove the 3 screws

indicated with red arrows. Once the screws have been removed,

carefully and gently detach the side panel.

The picture below shows how the gear

should be set once it has been placed within

the panel. To insert the gear in this panel,

slide the flag (which is the longest part of the

gear) through the right side opening (green

arrow on right side) and then slide the gear to

the left. Once you have done this, hold the

flag in place and place the panel back on the

cartridge. Place the screws back in place and

your cartridge is ready to be used.

Brother – TN420 / TN450

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the

side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can, or use a vacuum

with a hose for best results (if possible).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen

the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.

Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling

hole and insert it into the hole. If the toner stops flowing before the cartridge is full,

simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.

Once the cartridge is full, seal the hole with the plug by twisting it until it is completely

seated. Now gently shake the cartridge side to side to distribute the toner.

Installing the Reset Gear

Some of the starter cartridges don’t contain reset gears, or even a panel that allows

one to be installed. For this we have added two illustrations on the right. When you

purchase the reset gear, it may come with a new side panel to replace the old one with

(this is only for starter cartridges). The illustrations to the right show how the cartridge

may look without the gear, and how it should look once its installed.

If you are using a cartridge other than a starter cartridge (a cartridge that didn’t come

with the printer), then you only need to reset the gear. Putting it in the same position

as shown in the picture to the right (the illustration with the gear already on the

Brother – TN-330 / TN-360

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before

refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results (if

possible). ***Use only 1/2 the bottle of toner to refill a TN-330 cartridge***

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and

allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making

to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner

stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside

down and tap it on a table. Once the cartridge is full, seal the hole with the plug by twisting it until it

is completely seated. Now gently shake the cartridge side to side to distribute the toner.

Installing Reset Gear on Starter Cartridges

1. Remove the screws circled in red in the illustration above. Carefully detach the

panel from the cartridge.

2. Reset the flag gear by turning it into the correct position. The picture on the

right shows the flag gear in the correct position.

3. Screw the panel back into place, and your cartridge is ready.

Brother – TN430/460/560

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool

General Refilling Procedures:

CRITICAL NOTE: You must remove all of the remaining old toner BEFORE refilling

otherwise you will get gray hazy prints.

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the

side of the cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen

the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.

Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling

hole and insert it into the hole. If the toner stops flowing before the cartridge is full,

simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.

Once the cartridge is full, seal the hole with the plug by twisting it until it is completely

seated. Now gently shake the cartridge side to side to distribute the toner.

Brother – TN540 / 550 / 570 / 580 / 650

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the

side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can, or use a vacuum

with a hose for best results (if possible).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen

the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.

Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling

hole and insert it into the hole. If the toner stops flowing before the cartridge is full,

simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.

Once the cartridge is full, seal the hole with the plug by twisting it until it is completely

seated. Now gently shake the cartridge side to side to distribute the toner.

Installing Reset Gear on Starter Cartridges

Brother – TN-110/TN-115

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 Flat head screw driver (Not Included)

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the

cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before

refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results

(if possible). For the TN-110, please be sure you only use half the toner in the bottle. Do not

overfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can and

will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and

allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making

to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner

stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle

upside down and tap it on a table. Once the cartridge is full, seal the hole with the plug by twisting

it until it is completely seated. Now gently shake the cartridge side to side to distribute the toner.

Resetting the counter (Reset Gear)

Using the illustration below as a guide, remove the 2 screws

indicated with red circles. Once the screws have been removed,

carefully and gently (with a Flat head screwdriver) unlock the

side panel and remove the side cap.

After removing the side panel (as instructed

on the left); The 2 pictures on the right show

how the gear should be set in order to reset

the counter. Carefully remove the gear and

the pin holding it in place. Turn the gear

clock wise and replace it so that it meshes

and matches the “Properly Reset” picture to

the right. Re-install the pin so that it holds

the gear down. Once the gear has been reset,

re-install the side cap, and place the screws

firmly back in place. Your cartridge is ready

to be used.

Brother – TN-210/TN-215

REQUIRED FOR A SUCCESSFUL REFILL: CLICK HERE TO GO THE INDEX

 Toner

 1 funnel cap

 Flat head screw driver (Not Included)

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can and will damage a cartridge. Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge is full, seal the hole with the plugby twisting it until it is completely seated. Now gently shake the cartridge side to side to distribute the toner.

Resetting the counter (Reset Gear)

Using the illustration below as a guide, remove the 2 screws

indicated with red circles. Once the screws have been removed,

carefully and gently (with a Flat head screwdriver) unlock the side

panel and remove the side cap.

After removing the side panel (as instructed on the left); The picture on the right show

how the gear should be set in order to reset the counter. Once the gear has been reset,

re-install the side cap, and place the screws firmly back in place. Your cartridge is ready

to be used.

Brother – TN-310/TN-315/TN-320/

TN-325/TN-328/TN-335

REQUIRED FOR A SUCCESSFUL REFILL: CLICK HERE TO GO THE INDEX

 Toner

 1 funnel cap

 Flat head screw driver (Not Included)

General Refilling Procedures:

Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the cartridge.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can and will damage a cartridge.Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and allow it to flow freely.

Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge is full, seal the hole with the plug by twisting it until it is completely seated. Now gently shake the cartridge side to side to distribute the toner.

Resetting the counter (Reset Gear)

Using the illustration below as a guide, remove the 2 screws

indicated with red circles. Once the screws have been removed,

carefully and gently (with a Flat head screwdriver) unlock the side

panel and remove the side cap.

12591, 8R7880, 8R882

1. The filling holes are located under the plastic cap. Use a thin flathead screw\driver or

knife to remove the cap. Important: Do not to damage the sensors on the back of

the cartridge.

2. Connect the needle to the syringe and fill with ink.

3. Insert the needle into the matching hole of the color to be refilled, (see diagram

above) and push into the cartridge. Note: You will feel a slight pressure because the

cartridge contains a sponge.

4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble

at the top of the sponge. Important: Do not overfill. Keep the sponge inside the

cartridge white.

5. Rinse the needle and syringe with water and dry between each color refilling or store

for future use.

6. The cover can be reattached with a piece of tape

Black Cartridges:

8R7881

1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge.

(Do not remove the cap.)

2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print

Head Cleaner and inject into the cartridge. Reinsert cartridge into printer and print

5 test pages.

3. Fill the syringe with ink. Insert the needle into the filling hole and push down into

the cartridge. Inject up to 20 ml. of ink or until the cartridge is full.

Note: Immediately refill any empty cartridges.

8R7660, 8R7661, 8R7662, 8R7663

1. The filling hole is located under the label as shown. Just peel back the label

leaving it still connected to the cartridge, do not remove completely.

2. Use the provided eyelet screw to drill a filling hole on the top of the

cartridge(s) opposite side of the sponge.

3. Connect the needle to the syringe and fill with ink.

4. Insert the needle into the filling hole and inject about 5 ml of ink.

5. Use the provided plug to seal the hole. Note: If the cartridge has been empty/

dry, the sponge will no longer accept any ink which will cause the cartridge

to leak. Pull the label back into place and use a piece of tape to hold it in place.

6. Rinse the syringe with water and dry between each color refill or store for

future use.

7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per

printer instructions.

Note: Immediately refill any empty cartridges

8R7638

1. Using the included hole making tool make a filling hole in the front of the

cartridge about 1/2” from the top.

2. Connect the needle to the syringe and fill with ink.

3. Insert the filling needle into the hole and aim it towards the center of the cartridge.

Note: The cartridge contains a dense sponge made out of felt. As soon as

the needle touches the felt stop pushing in the needle.

4. Inject up to 40 ml. of ink or until ink bubbles at the filling hole.

5. Use either the plug included in the kit or a piece of tape to seal the filling hole.

6. Rinse the syringe and needle with water and dry for future use.

7. Reinsert the cartridge and run a priming cycle as per printer instructions.

Note: Empty cartridges should be refilled immediately.

8R7903, 8R7904

1. The filling holes are located under the plastic cap. The cap is held in place with

a pin at the each corner. Use a thin flathead screwdriver or knife to remove the

cap. Important: Do not to damage the sensors on the back of the cartridge.

2. Connect the needle to the syringe and fill with ink.

3. Insert the needle into the matching hole of the color to be refilled, (see diagram

above) and push into the cartridge. Note: You will feel a slight pressure

because the cartridge contains a sponge.

4. Inject about 10 ml. of ink, per color, into the cartridge until the ink begins to

bubble at the top of the sponge. Important: Do not overfill. Keep the sponge

inside the cartridge white.

5. Rinse the needle and syringe with water and dry between each color refilling

or store for future use.

6. The cover can be put back onto the cartridge by pressing it down.

8R12728

1. Use the eyelet screw to make the filling hole in the small notch on the corner

located next to the “1” shown on the label.

2. Fill the syringe with ink and inject about 8 ml. of ink until the ink tank is full.

3. Use a piece of tape to seal the filling hole, make sure that the tape is stuck to

the cartridge.

4. Rinse the syringe with water and dry for future use, or use with a different

color ink.

5. Reinsert the cartridge and run a priming cycle as per printer instructions.

Note: Immediately refill any empty cartridges.

8R7971, 8R7972, 8R7973, 8R7974

1. The filling hole is located under the label on the top of the cartridge. Use the

empty needle to pierce through the label to make the filling hole.

2. Fill the syringe with ink and inject about 4 ml. of ink until the ink tank is full.

3. Use a piece of tape to seal the filling hole, make sure that the tape is stuck to

the cartridge

4. Rinse the syringe with water and dry for future use, or use with a different

color ink.

5. Reinsert the cartridge and run a priming cycle as per printer instructions.

Note: Immediately refill any empty cartridges.