Canon - E16/E20/E31/E40

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool (Not Included, Sold Separately)

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Remove the tool, place it

back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,

it must be removed, as this can damage your cartridge or cause print defects. If the

piece remains in the tool, wait for the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner.

Canon - L50

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug (electrical or duct tape will do as well)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Remove the tool, place it

back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,

it must be removed, as this can damage your cartridge or cause print defects. If the

piece remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can, or use a vacuum

with a hose for best results (if possible).

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug or electrical tape (Duct tape will do as

well).

Note: If there are gears that rotate near the refill hold created, do not use the plug,

instead use electrical tape or duct tape to seal the hole.

Gently rock the cartridge from side to side for about 5-10 seconds to distribute the

toner in the hopper. Your cartridge is now ready for use.

Canon – S35

Canon – X25

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool (Not Included, Sold Separately)

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Make sure to keep the

hole on the flat surface of the cartridge and not on the curved edge. Remove the tool,

place it back on its stand and unplug it. If the small piece of plastic has fallen into the

cartridge, it must be removed, as this can damage your cartridge or cause print defects.

If the piece remains in the tool, wait for the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner.

Canon – F100

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the tan portion of the cartridge on your right. Position the copper

bit on the cartridge in the spot indicated by the photograph and push gently until it

melts a hole in the cartridge. Remove the tool, place it back on its stand and unplug it.

If the small piece of plastic has fallen into the cartridge, it must be removed, as this can

damage your cartridge or cause print defects. If the piece remains in the tool, wait for

the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner

CANON A30, A15

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole plug (electrical or duct tape will do as well)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes

before using. Position the copper bit on the cartridge in the spot indicated by the photograph

and push gently until it melts a hole in the cartridge. Remove the tool, place it

back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,

it must be removed, as this can damage your cartridge or cause print defects. If the

piece remains in the tool, wait for the tool to cool down and pry it out.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually

damage the photo-optic drum. Instead hold one end of the cartridge up off the table

and twist the plug until it fully sealed. Now gently shake the cartridge side to side to

distribute the toner.

CANON FX-8
CANON S-35

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 Duct Tape

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in the photograph and

push gently until it melts a hole in the cartridge. Make sure to keep the hole on the flat surface

of the cartridge and not on the curved edge. Remove the tool, place it back on its stand

and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed,

as this can damage your cartridge or cause print defects. If the piece remains in the tool,

wait for the tool to cool down and pry it out.

Create a hole on the opposite end where the waste toner is located. Empty the waste toner

as much as possible, then seal it with electrical tape or duct tape. Once you have sealed it

proceed to the next step.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and

insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove

the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge

is full seal the hole with the tape

Firmly secure the tape and then gently rock the cartridge from side to side to distribute the

new toner.

CANON FX-9/FX-10

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional - Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in photograph A and

push gently until it melts a hole in the cartridge. Remove the tool, place it back on its stand

and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed,

as this can damage your cartridge or cause print defects. If the piece remains in the tool,

wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible

before refilling. Dispose of toner properly into a trash can, or use a vacuum with a

hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner

powder into the cartridge. Use half the bottle now, and the rest at a later time. Overfilling

can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and

insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove

the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge

is full seal the hole with the plug.

Do not press down on the plug since the cartridge is resting on a table this can actually damage

the photo-optic drum. Instead hold one end of the cartridge up off the table and twist

the plug until it fully sealed. Now gently shake the cartridge side to side to distribute the

toner.

CANON CARTRIDGE 106

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before

using. Position the copper bit on the cartridge in the spot indicated in photograph A

and push gently until it melts a hole in the cartridge. Make sure to keep the hole on the

flat surface of the cartridge and not on the curved edge. Remove the tool, place it back

on its stand and unplug it. If the small piece of plastic has fallen into the cartridge, it

must be removed, as this can damage your cartridge or cause print defects. If the piece

remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as

possible before refilling. Dispose of toner properly into a trash can . Do not overfill

the cartridge by pouring the entire toner powder into the cartridge. Use half or a

fourth of the bottle now, and the rest at a later time. Overfilling can and will damage

a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the

toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach

the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole

and insert it into the hole. If the toner stops flowing before the cartridge is full, simply

remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once

the cartridge is full seal the hole properly.

Now gently shake the cartridge side to side to distribute the toner.

CANON CARTRIDGE 120

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using.

Position the copper bit on the cartridge in the spot indicated in photograph A and push gently until

it melts a hole in the cartridge. Make sure to keep the hole on the flat surface of the cartridge and not

on the curved edge. Remove the tool, place it back on its stand and unplug it. If the small piece of

plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge or cause

print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before

refilling. Dispose of toner properly into a trash can . Do not overfill the cartridge by pouring the

entire toner powder into the cartridge. Use half or a fourth of the bottle now, and the rest at a

later time. Overfilling can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and

allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making

to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the

toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle

upside down and tap it on a table. Once the cartridge is full seal the hole properly.

CANON CARTRIDGE 128
CANON IMAGECLASS MF4420

REQUIRED FOR A SUCCESSFUL REFILL:

 Toner

 1 funnel cap

 1 hole (Optional Electrical Tape/Duct Tape)

 Toner Hole Making Tool

General Refilling Procedures:

Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using.

Position the copper bit on the cartridge in the spot indicated in photograph A and push gently

until it melts a hole in the cartridge. Make sure to keep the hole on the flat surface of the cartridge

and not on the curved edge. Remove the tool, place it back on its stand and unplug it. If the small

piece of plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge

or cause print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.

IMPORTANT: You must dispose of any original toner in the cartridge as much as possible

before refilling. Dispose of toner properly into a trash can . Do not overfill the cartridge by

pouring the entire toner powder into the cartridge. Use half or a fourth of the bottle now, and

the rest at a later time. Overfilling can and will damage a cartridge.

Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner

and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap

making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole.

If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn

the bottle upside down and tap it on a table. Once the cartridge is full seal the hole properly.

BCI-21 Black & 24 Black
BCI-21 Color & 24 Color

1. Use a knife to remove the top of cartridge(s).
2. Use the included eyelet screw to enlarge the filling hole(s) in the top of the cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the syringe into the correct filling hole, (See diagram below for filling hole color)
and push into the center of the cartridge. Note: You may feel a slight pressure because
the cartridge contains a sponge.
5. Inject up to 5 ml. of ink, per color, into the cartridge.
6. Reposition the top and secure with a piece of tape.
7. Rinse the syringe with water and dry between each color filling or store for future use.
8. Reinsert the cartridge(s) and run a cleaning cycle as per printer instructions

BC-20 & BC-23

High Capacity Cartridge

1. Use the eyelet screw to remove plug located on top of the cartridge.

2. Connect the needle to the syringe and fill with ink.

3. Insert the syringe through the filling hole and push into the cartridge. Note: You may

feel a slight pressure because the cartridge contains a sponge.

4. Inject up to 30 ml. of ink then reseal the cartridge with the plug that was removed

from step 1.

5. Rinse the syringe with water and dry for future use, or use with a different color ink.

6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.

Note: Immediately refill any empty cartridges.

BJI-201BK HC, BJI-201BK, BJI-201C, BJI-201M, BJI-201Y

1. With the cartridge upside down, using a screwdriver, push in the ball bearing that seals

the filling hole. NOTE: There are several versions of these cartridges. One version

has the filling hole under the label on the top of the cartridge. Another version does

not have a ball bearing at all. In this case it would be necessary to make a hole for

the needle to be inserted. Make this hole in the same spot where the ball bearing

would be located, as shown below. Seal hole with the plug provided.

2. Connect the needle to the syringe and fill with ink.

3. Inject about 5 ml. of ink into the filling hole until the tank is full.

4. Use the included plug to seal the filling hole, make sure that the plug is sitting flush in

the cartridge. Additional Note: If the cartridge has been empty/dry, the sponge will

no longer accept any ink which will cause the cartridge to leak.

5. Rinse the syringe with water and dry for future use, or use with a different color ink.

6. Reinsert the cartridge and run a priming cycle as per printer instructions.

Note: Immediately refill any empty cartridges.

BC-01, BC-02, BC-05, BX-02, BX-03,

1. Use the eyelet screw to remove plug located on the top side of the cartridge.

FOR BX-03 ONLY: A hole must be made on the top of the cartridge by using

the hole making tool included in the kit. . Firmly hold the handle of the

tool and begin twisting the tool into the top corner of the cartridge. Continue

twisting until it pierces the plastic cover. Once the plastic to is pierced, making

the rest of the hole will go very quickly.

2. Connect the needle to the syringe and fill with ink.

3. Insert the syringe through the filling hole and push into the cartridge. Note:

You may feel a slight pressure because the cartridge contains a sponge.

4. Inject up to 30 ml. of ink then reseal the cartridge with the plug that was

removed from step 1. FOR BX-03 ONLY: Use the plug provided in the kit to

seal the cartridge.

5. Rinse the syringe with water and dry for future use, or use with a different

color ink.

6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.

Note: Immediately refill any empty cartridges.

BCI-60, BCI-61, BCI-62

1. The filling holes are located under the label as shown. Just peel back the label

leaving it still connected to the cartridge, do not remove completely.

2. Use the provided eyelet screw to widen the filling hole(s) in the top of the

cartridge(s).

3. Connect the needle to the syringe and fill with ink.

4. Insert the needle into the widen filling hole. Note: This cartridge has a

sponge so you may feel a slight pressure. Inject about 10 ml. of ink, per

color until the ink bubbles up.

5. Pull the label back into place and use a piece of tape to hold it in place.

6. Rinse the syringe with water and dry between each color refill or store for

future use.

7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per

printer instructions.

Note: Immediately refill any empty cartridge

BCI-3e (All Colors), BCI-3, (All Colors), BCI-5 (All Colors),
BCI-6 (All Colors), Cli-8 (All Colors), PGI-5, PGI-
220, CLI-221 (All Colors), PGI-225, CLI-226 (All Colors)

Method #2

1. Use electrical or duct tape to seal the Air Vent found on the top of the cartridge.

Note: Make sure tape is completely covering the vent.

2. Remove the label partially, only to expose the ball bearing underneath. Then use a screwdriver

or an L. tool to push the ball bearing into the cartridge. This will give access to the

filling hole.

3. Connect the needle to the syringe and fill with ink.

4. Use your finger as a plug by covering the outlet port. Keep your finger on the outlet port

until you have finished refilling and the refill hole is plugged. If you let go any time earlier,

ink may and can spill out of that outlet.

5. Inject about 10 ml. of ink into the filling hole or until the ink chamber is full. Be sure to

leave enough room in the ink chamber for the silicon plug, it will create pressure when

inserted.

6. Put a silicone plug in the refill hole to seal it, make sure it is air tight. If extra silicone from

the plug is sticking out, you may trim it down to a practical size. Be sure to leave enough

to make it easy for you to remove the next time you wish to refill the cartridge.

7. Remove your finger from the outlet (small drops may leak out, but once the cartridge pressure

stabilizes itself, it will stop) and remove the tape from earlier off the vent.

8. Rinse the syringe with water and dry for future use, or use with a different color ink.

9. Reinsert the cartridge and run a priming cycle as per printer instructions.

Note: If the cartridge continuously leaks, place the cartridge on its side until the dripping

stops. Also, check the seal on the cartridge to make sure it is airtight.

BC-22e

1. Use the eyelet screw to remove the plugs located on top of the cartridge.

2. Connect the needle to the syringe and fill with ink.

3. Insert the syringe through the filling hole and push into the cartridge. Note:

You may feel a slight pressure because the cartridge contains a sponge.

4. Inject up to 10 ml. of ink, per color, then reseal the cartridge with the plug that

was removed from step 1.

5. Rinse the syringe with water and dry for future use, or use with a different

color ink.

6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.

Note: Immediately refill any empty cartridges.

PG-30/PG-40/PG-50
PG-210
CL-31/CL-41/CL-51
CL-211 CL-52

1. Remove the label from the top of cartridge

2. Using the drill tool, widen the refill holes for each color. Please use the illustrations on the

right for color guidance.

3. Attach the needle to syringe and load syringe with 6 ml of ink for each color in the color cartridge

or 20 ml for the black cartridge.

4. Insert needle into corresponding color and penetrate the sponge inside. Insert the needle only

a 1/4 of an inch in.

If the needle penetrates to the bottom of the cartridge, the cartridge will leak and is not

salvageable.

5. SLOWLY inject the ink into the cartridge. Reverse the process and pull about 1 ml of ink if it

has spilled out the top of the cartridge.

6. Repeat steps 5, 6, 7, 8 until all colors have been injected.

7. Clean off the top of the cartridge. Place tape over the top of the cartridge so it covers every

hole.

8. Use a pin and put a small hole (vent hole) through the tape for each hole on the top of the

cartridge.

This is important, don’t skip this step. The cartridge must be vented to atmosphere or it will

not work.

9. Reinstall in printer and run one or two cleaning cycles until the cartridge begins to print correctly