12591, 8R7880, 8R882
1. The filling holes are located under the plastic cap. Use a thin flathead screw\driver or
knife to remove the cap. Important: Do not to damage the sensors on the back of
the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram
above) and push into the cartridge. Note: You will feel a slight pressure because the
cartridge contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble
at the top of the sponge. Important: Do not overfill. Keep the sponge inside the
cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling or store
for future use.
6. The cover can be reattached with a piece of tape
Black Cartridges:
8R7881
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge.
(Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print
Head Cleaner and inject into the cartridge. Reinsert cartridge into printer and print
5 test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into
the cartridge. Inject up to 20 ml. of ink or until the cartridge is full.
Note: Immediately refill any empty cartridges.
8R7660, 8R7661, 8R7662, 8R7663
1. The filling hole is located under the label as shown. Just peel back the label
leaving it still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to drill a filling hole on the top of the
cartridge(s) opposite side of the sponge.
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the filling hole and inject about 5 ml of ink.
5. Use the provided plug to seal the hole. Note: If the cartridge has been empty/
dry, the sponge will no longer accept any ink which will cause the cartridge
to leak. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for
future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per
printer instructions.
Note: Immediately refill any empty cartridges
8R7638
1. Using the included hole making tool make a filling hole in the front of the
cartridge about 1/2” from the top.
2. Connect the needle to the syringe and fill with ink.
3. Insert the filling needle into the hole and aim it towards the center of the cartridge.
Note: The cartridge contains a dense sponge made out of felt. As soon as
the needle touches the felt stop pushing in the needle.
4. Inject up to 40 ml. of ink or until ink bubbles at the filling hole.
5. Use either the plug included in the kit or a piece of tape to seal the filling hole.
6. Rinse the syringe and needle with water and dry for future use.
7. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Empty cartridges should be refilled immediately.
8R7903, 8R7904
1. The filling holes are located under the plastic cap. The cap is held in place with
a pin at the each corner. Use a thin flathead screwdriver or knife to remove the
cap. Important: Do not to damage the sensors on the back of the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram
above) and push into the cartridge. Note: You will feel a slight pressure
because the cartridge contains a sponge.
4. Inject about 10 ml. of ink, per color, into the cartridge until the ink begins to
bubble at the top of the sponge. Important: Do not overfill. Keep the sponge
inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling
or store for future use.
6. The cover can be put back onto the cartridge by pressing it down.
8R12728
1. Use the eyelet screw to make the filling hole in the small notch on the corner
located next to the “1” shown on the label.
2. Fill the syringe with ink and inject about 8 ml. of ink until the ink tank is full.
3. Use a piece of tape to seal the filling hole, make sure that the tape is stuck to
the cartridge.
4. Rinse the syringe with water and dry for future use, or use with a different
color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
8R7971, 8R7972, 8R7973, 8R7974
1. The filling hole is located under the label on the top of the cartridge. Use the
empty needle to pierce through the label to make the filling hole.
2. Fill the syringe with ink and inject about 4 ml. of ink until the ink tank is full.
3. Use a piece of tape to seal the filling hole, make sure that the tape is stuck to
the cartridge
4. Rinse the syringe with water and dry for future use, or use with a different
color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
0 komentar:
Posting Komentar