Brother – TN250
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
General Refilling Procedures:
Using your thumb, lift up the black plastic tab so that it unlocks from the cartridge
body. Rotate the entire black piece toward you. This will reveal a toner filling port.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full, twist the entire black plastic piece away from you until the tab
locks back in place.
Brother – TN350
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the
side of the cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as
possible before refilling. Dispose of toner properly into a trash can, or use a vacuum
with a hose for best results (if possible).
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen
the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.
Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling
hole and insert it into the hole. If the toner stops flowing before the cartridge is full,
simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.
Once the cartridge is full, seal the hole with the plug by twisting it until it is completely
seated. Now gently shake the cartridge side to side to distribute the toner.
Installing Reset Gear on Starter Cartridges
Using the illustration below as a guide, remove the 3 screws
indicated with red arrows. Once the screws have been removed,
carefully and gently detach the side panel.
The picture below shows how the gear
should be set once it has been placed within
the panel. To insert the gear in this panel,
slide the flag (which is the longest part of the
gear) through the right side opening (green
arrow on right side) and then slide the gear to
the left. Once you have done this, hold the
flag in place and place the panel back on the
cartridge. Place the screws back in place and
your cartridge is ready to be used.
Brother – TN420 / TN450
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the
side of the cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as
possible before refilling. Dispose of toner properly into a trash can, or use a vacuum
with a hose for best results (if possible).
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen
the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.
Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling
hole and insert it into the hole. If the toner stops flowing before the cartridge is full,
simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.
Once the cartridge is full, seal the hole with the plug by twisting it until it is completely
seated. Now gently shake the cartridge side to side to distribute the toner.
Installing the Reset Gear
Some of the starter cartridges don’t contain reset gears, or even a panel that allows
one to be installed. For this we have added two illustrations on the right. When you
purchase the reset gear, it may come with a new side panel to replace the old one with
(this is only for starter cartridges). The illustrations to the right show how the cartridge
may look without the gear, and how it should look once its installed.
If you are using a cartridge other than a starter cartridge (a cartridge that didn’t come
with the printer), then you only need to reset the gear. Putting it in the same position
as shown in the picture to the right (the illustration with the gear already on the
Brother – TN-330 / TN-360
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before
refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results (if
possible). ***Use only 1/2 the bottle of toner to refill a TN-330 cartridge***
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and
allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making
to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner
stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside
down and tap it on a table. Once the cartridge is full, seal the hole with the plug by twisting it until it
is completely seated. Now gently shake the cartridge side to side to distribute the toner.
Installing Reset Gear on Starter Cartridges
1. Remove the screws circled in red in the illustration above. Carefully detach the
panel from the cartridge.
2. Reset the flag gear by turning it into the correct position. The picture on the
right shows the flag gear in the correct position.
3. Screw the panel back into place, and your cartridge is ready.
Brother – TN430/460/560
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole plug
Toner Hole Making Tool
General Refilling Procedures:
CRITICAL NOTE: You must remove all of the remaining old toner BEFORE refilling
otherwise you will get gray hazy prints.
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the
side of the cartridge.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen
the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.
Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling
hole and insert it into the hole. If the toner stops flowing before the cartridge is full,
simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.
Once the cartridge is full, seal the hole with the plug by twisting it until it is completely
seated. Now gently shake the cartridge side to side to distribute the toner.
Brother – TN540 / 550 / 570 / 580 / 650
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the
side of the cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as
possible before refilling. Dispose of toner properly into a trash can, or use a vacuum
with a hose for best results (if possible).
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen
the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle.
Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling
hole and insert it into the hole. If the toner stops flowing before the cartridge is full,
simply remove the toner, close the cap, turn the bottle upside down and tap it on a table.
Once the cartridge is full, seal the hole with the plug by twisting it until it is completely
seated. Now gently shake the cartridge side to side to distribute the toner.
Installing Reset Gear on Starter Cartridges
Brother – TN-110/TN-115
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
Flat head screw driver (Not Included)
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the
cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before
refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results
(if possible). For the TN-110, please be sure you only use half the toner in the bottle. Do not
overfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can and
will damage a cartridge.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and
allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making
to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner
stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle
upside down and tap it on a table. Once the cartridge is full, seal the hole with the plug by twisting
it until it is completely seated. Now gently shake the cartridge side to side to distribute the toner.
Resetting the counter (Reset Gear)
Using the illustration below as a guide, remove the 2 screws
indicated with red circles. Once the screws have been removed,
carefully and gently (with a Flat head screwdriver) unlock the
side panel and remove the side cap.
After removing the side panel (as instructed
on the left); The 2 pictures on the right show
how the gear should be set in order to reset
the counter. Carefully remove the gear and
the pin holding it in place. Turn the gear
clock wise and replace it so that it meshes
and matches the “Properly Reset” picture to
the right. Re-install the pin so that it holds
the gear down. Once the gear has been reset,
re-install the side cap, and place the screws
firmly back in place. Your cartridge is ready
to be used.
Brother – TN-210/TN-215
REQUIRED FOR A SUCCESSFUL REFILL: CLICK HERE TO GO THE INDEX
Toner
1 funnel cap
Flat head screw driver (Not Included)
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can and will damage a cartridge. Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge is full, seal the hole with the plugby twisting it until it is completely seated. Now gently shake the cartridge side to side to distribute the toner.
Resetting the counter (Reset Gear)
Using the illustration below as a guide, remove the 2 screws
indicated with red circles. Once the screws have been removed,
carefully and gently (with a Flat head screwdriver) unlock the side
panel and remove the side cap.
After removing the side panel (as instructed on the left); The picture on the right show
how the gear should be set in order to reset the counter. Once the gear has been reset,
re-install the side cap, and place the screws firmly back in place. Your cartridge is ready
to be used.
Brother – TN-310/TN-315/TN-320/
TN-325/TN-328/TN-335
REQUIRED FOR A SUCCESSFUL REFILL: CLICK HERE TO GO THE INDEX
Toner
1 funnel cap
Flat head screw driver (Not Included)
General Refilling Procedures:
Use a Flat head screwdriver to pop out the large plastic plug found on the side of the side of the cartridge.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before refilling. Dispose of toner properly into a trash can, or use a vacuum with a hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner powder into the cartridge. Overfilling can and will damage a cartridge.Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and allow it to flow freely.
Remove the cap and pull the seal off the bottle. Attach the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge is full, seal the hole with the plug by twisting it until it is completely seated. Now gently shake the cartridge side to side to distribute the toner.
Resetting the counter (Reset Gear)
Using the illustration below as a guide, remove the 2 screws
indicated with red circles. Once the screws have been removed,
carefully and gently (with a Flat head screwdriver) unlock the side
panel and remove the side cap.
4 komentar:
Thanks for this very important and useful post. Thanks for helping out in providing step by step process. Sometimes cartridges and toners are as costly as new printer and hence refilling is always best. Toner refilling does save a lot of money. Keep writing more on other printer issues as well. Thanks again.
Thanks for the information and links you shared. This is so useful and quite informative! I will be back on your next writing on laser toner cartridge.
Toner refilling is very easy and it is quite a good business. Many people opt for refilling because original toners are very costly. As a service engineer of private Canon toner refilling centers in Chennai reading posts related to printers gives me knowledge. Thank you.
Good post on printer refilling. The post is really very informative. Refilling saves a lot of money rather than buying new ink cartridges or laser cartridges. We provide Laser toner refilling in Chennai and we do this work on a daily basis and hence like to read post regarding printers.
Posting Komentar