Canon - E16/E20/E31/E40
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole plug
Toner Hole Making Tool (Not Included, Sold Separately)
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes
before using. Position the copper bit on the cartridge in the spot indicated by the photograph
and push gently until it melts a hole in the cartridge. Remove the tool, place it
back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,
it must be removed, as this can damage your cartridge or cause print defects. If the
piece remains in the tool, wait for the tool to cool down and pry it out.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full seal the hole with the plug.
Do not press down on the plug since the cartridge is resting on a table this can actually
damage the photo-optic drum. Instead hold one end of the cartridge up off the table
and twist the plug until it fully sealed. Now gently shake the cartridge side to side to
distribute the toner.
Canon - L50
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole plug (electrical or duct tape will do as well)
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes
before using. Position the copper bit on the cartridge in the spot indicated by the photograph
and push gently until it melts a hole in the cartridge. Remove the tool, place it
back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,
it must be removed, as this can damage your cartridge or cause print defects. If the
piece remains in the tool, wait for the tool to cool down and pry it out.
IMPORTANT: You must dispose of any original toner in the cartridge as much as
possible before refilling. Dispose of toner properly into a trash can, or use a vacuum
with a hose for best results (if possible).
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full seal the hole with the plug or electrical tape (Duct tape will do as
well).
Note: If there are gears that rotate near the refill hold created, do not use the plug,
instead use electrical tape or duct tape to seal the hole.
Gently rock the cartridge from side to side for about 5-10 seconds to distribute the
toner in the hopper. Your cartridge is now ready for use.
Canon – S35
Canon – X25
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole plug
Toner Hole Making Tool (Not Included, Sold Separately)
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes
before using. Position the copper bit on the cartridge in the spot indicated by the photograph
and push gently until it melts a hole in the cartridge. Make sure to keep the
hole on the flat surface of the cartridge and not on the curved edge. Remove the tool,
place it back on its stand and unplug it. If the small piece of plastic has fallen into the
cartridge, it must be removed, as this can damage your cartridge or cause print defects.
If the piece remains in the tool, wait for the tool to cool down and pry it out.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full seal the hole with the plug.
Do not press down on the plug since the cartridge is resting on a table this can actually
damage the photo-optic drum. Instead hold one end of the cartridge up off the table
and twist the plug until it fully sealed. Now gently shake the cartridge side to side to
distribute the toner.
Canon – F100
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole plug
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes
before using. Position the tan portion of the cartridge on your right. Position the copper
bit on the cartridge in the spot indicated by the photograph and push gently until it
melts a hole in the cartridge. Remove the tool, place it back on its stand and unplug it.
If the small piece of plastic has fallen into the cartridge, it must be removed, as this can
damage your cartridge or cause print defects. If the piece remains in the tool, wait for
the tool to cool down and pry it out.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full seal the hole with the plug.
Do not press down on the plug since the cartridge is resting on a table this can actually
damage the photo-optic drum. Instead hold one end of the cartridge up off the table
and twist the plug until it fully sealed. Now gently shake the cartridge side to side to
distribute the toner
CANON A30, A15
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole plug (electrical or duct tape will do as well)
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes
before using. Position the copper bit on the cartridge in the spot indicated by the photograph
and push gently until it melts a hole in the cartridge. Remove the tool, place it
back on its stand and unplug it. If the small piece of plastic has fallen into the cartridge,
it must be removed, as this can damage your cartridge or cause print defects. If the
piece remains in the tool, wait for the tool to cool down and pry it out.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full seal the hole with the plug.
Do not press down on the plug since the cartridge is resting on a table this can actually
damage the photo-optic drum. Instead hold one end of the cartridge up off the table
and twist the plug until it fully sealed. Now gently shake the cartridge side to side to
distribute the toner.
CANON FX-8
CANON S-35
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
Duct Tape
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before
using. Position the copper bit on the cartridge in the spot indicated in the photograph and
push gently until it melts a hole in the cartridge. Make sure to keep the hole on the flat surface
of the cartridge and not on the curved edge. Remove the tool, place it back on its stand
and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed,
as this can damage your cartridge or cause print defects. If the piece remains in the tool,
wait for the tool to cool down and pry it out.
Create a hole on the opposite end where the waste toner is located. Empty the waste toner
as much as possible, then seal it with electrical tape or duct tape. Once you have sealed it
proceed to the next step.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and
insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove
the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge
is full seal the hole with the tape
Firmly secure the tape and then gently rock the cartridge from side to side to distribute the
new toner.
CANON FX-9/FX-10
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole (Optional - Electrical Tape/Duct Tape)
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before
using. Position the copper bit on the cartridge in the spot indicated in photograph A and
push gently until it melts a hole in the cartridge. Remove the tool, place it back on its stand
and unplug it. If the small piece of plastic has fallen into the cartridge, it must be removed,
as this can damage your cartridge or cause print defects. If the piece remains in the tool,
wait for the tool to cool down and pry it out.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible
before refilling. Dispose of toner properly into a trash can, or use a vacuum with a
hose for best results (if possible). Do not overfill the cartridge by pouring the entire toner
powder into the cartridge. Use half the bottle now, and the rest at a later time. Overfilling
can and will damage a cartridge.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole and
insert it into the hole. If the toner stops flowing before the cartridge is full, simply remove
the toner, close the cap, turn the bottle upside down and tap it on a table. Once the cartridge
is full seal the hole with the plug.
Do not press down on the plug since the cartridge is resting on a table this can actually damage
the photo-optic drum. Instead hold one end of the cartridge up off the table and twist
the plug until it fully sealed. Now gently shake the cartridge side to side to distribute the
toner.
CANON CARTRIDGE 106
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole (Optional Electrical Tape/Duct Tape)
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before
using. Position the copper bit on the cartridge in the spot indicated in photograph A
and push gently until it melts a hole in the cartridge. Make sure to keep the hole on the
flat surface of the cartridge and not on the curved edge. Remove the tool, place it back
on its stand and unplug it. If the small piece of plastic has fallen into the cartridge, it
must be removed, as this can damage your cartridge or cause print defects. If the piece
remains in the tool, wait for the tool to cool down and pry it out.
IMPORTANT: You must dispose of any original toner in the cartridge as much as
possible before refilling. Dispose of toner properly into a trash can . Do not overfill
the cartridge by pouring the entire toner powder into the cartridge. Use half or a
fourth of the bottle now, and the rest at a later time. Overfilling can and will damage
a cartridge.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the
toner and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach
the funnel cap making to sure it is on tightly. Tilt the funnel cap toward the filling hole
and insert it into the hole. If the toner stops flowing before the cartridge is full, simply
remove the toner, close the cap, turn the bottle upside down and tap it on a table. Once
the cartridge is full seal the hole properly.
Now gently shake the cartridge side to side to distribute the toner.
CANON CARTRIDGE 120
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole (Optional Electrical Tape/Duct Tape)
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using.
Position the copper bit on the cartridge in the spot indicated in photograph A and push gently until
it melts a hole in the cartridge. Make sure to keep the hole on the flat surface of the cartridge and not
on the curved edge. Remove the tool, place it back on its stand and unplug it. If the small piece of
plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge or cause
print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible before
refilling. Dispose of toner properly into a trash can . Do not overfill the cartridge by pouring the
entire toner powder into the cartridge. Use half or a fourth of the bottle now, and the rest at a
later time. Overfilling can and will damage a cartridge.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner and
allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap making
to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole. If the
toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn the bottle
upside down and tap it on a table. Once the cartridge is full seal the hole properly.
CANON CARTRIDGE 128
CANON IMAGECLASS MF4420
REQUIRED FOR A SUCCESSFUL REFILL:
Toner
1 funnel cap
1 hole (Optional Electrical Tape/Duct Tape)
Toner Hole Making Tool
General Refilling Procedures:
Rest the Hole Making Tool on its stand and plug into an outlet. Wait 3 full minutes before using.
Position the copper bit on the cartridge in the spot indicated in photograph A and push gently
until it melts a hole in the cartridge. Make sure to keep the hole on the flat surface of the cartridge
and not on the curved edge. Remove the tool, place it back on its stand and unplug it. If the small
piece of plastic has fallen into the cartridge, it must be removed, as this can damage your cartridge
or cause print defects. If the piece remains in the tool, wait for the tool to cool down and pry it out.
IMPORTANT: You must dispose of any original toner in the cartridge as much as possible
before refilling. Dispose of toner properly into a trash can . Do not overfill the cartridge by
pouring the entire toner powder into the cartridge. Use half or a fourth of the bottle now, and
the rest at a later time. Overfilling can and will damage a cartridge.
Before opening the bottle of toner, turn it upside down and tap it on a table to loosen the toner
and allow it to flow freely. Remove the cap and pull the seal off the bottle. Attach the funnel cap
making to sure it is on tightly. Tilt the funnel cap toward the filling hole and insert it into the hole.
If the toner stops flowing before the cartridge is full, simply remove the toner, close the cap, turn
the bottle upside down and tap it on a table. Once the cartridge is full seal the hole properly.
0 komentar:
Posting Komentar