Black Cartridges:
IN-700, LC11BK
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge.
(Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print
Head Cleaner and inject into the cartridge. Reinsert cartridge into printer and print 5
test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into the
cartridge. Inject up to 20 ml.. of ink or until the cartridge is full.
Note: Immediately refill any empty cartridges.
Color Cartridges:
IN-710C, LC11CL
1. The filling holes are located under the plastic cap. Use a thin flathead screwdriver orknife to remove the cap. Important: Do not to damage the sensors on the back of the
cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above)
and push into the cartridge. Note: You will feel a slight pressure because the cartridge
contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble at
the top of the sponge. Important: Do not overfill. Keep the sponge inside the cartridge
white.
5. Rinse the needle and syringe with water and dry between each color refilling or store
for future use.
6. The cover can be reattached with a piece of tape.
LC03BC, LC03MY
1. The filling hole is the same hole as the hole that connects to the printer.
2. Note: The cartridge is lined in a delicate Mylar bag and it is very important not to
insert the needle more than 3/4” or it is possible to pierce or tear the Mylar bag. Important:
It is very important to turn the cartridge as shown in the pictures. If you
have the cartridge reversed then you will put the wrong color of ink in the wrong fill
hole. Fill the syringe with ink and carefully insert the needle into the filling hole and
slowly inject about 4 ml. of ink into the cartridge.
3. Hold the cartridge up with the filling hole at the top. Using the syringe, remove any
trapped air in the cartridge by only inserting the tip of the needle and pulling up on
the plunger until all air is removed.
4. Remove the syringe and rinse with water and dry for future use, or to use with a different
color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
NOTE: It is not necessary to disassemble the cartridge to refill it and we strongly recommend
you do not.
LC01BK, LC01C, LC01M, LC01Y
1. The filling hole is located under the label as shown. Just peel back the label leaving it
still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to drill a filling hole on the top of the cartridge(s) into
the lower area.
3. Connect the needle to the syringe and fill with ink..
4. Insert the needle into the filling hole and inject about 10ml of ink.
5. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per printer
instructions.
LC02BK, LC02C, LC02M, LC02Y, LC21Bk, LC21C, LC21M, LC21Y,
LC31C, LC31M, LC31Y, LC31BK
1. Put a piece of tape over the bottom hole of the cartridge.
2. Use a flathead screwdriver to remove the cover by prying up the clip holding the cover
on the cartridge.
3. Using a knife remove both the small and large silver seals.
4. Underneath the large silver seal there are two holes (filling hole and vent hole), use the
eyelet screw to widen the hole closest to the center of the cartridge (not the hole closest
to the edge of the cartridge) Also widen the small hole located under the small silver
seal.
5. Connect the needle to the syringe and fill ink.
6. Insert the syringe into the hole that was located under the large silver seal. Note: You
may feel a slight pressure because the cartridge contains a sponge.
7. Inject about 7 ml. of ink and reseal the filling hole and vent hole with a piece of tape.
8. Insert the syringe into the small filling hole no more than 1/4” and inject approximately
3 ml. of ink and seal with a piece of tape.
9. Snap the plastic cover back onto the cartridge the same direction it came off.
10. Rinse the syringe with water and dry between each color refill or store for future use.
11. Remove the tape covering the bottom hole and reinsert the cartridge(s) and run a
priming cycle as per printer instructions.
Note: Immediately refill any empty cartridge
LC04C, LC04M, LC04Y, LC04BK
1. Put a piece of tape over the bottom hole of the cartridge.
2. Use a flathead screwdriver to remove the cover by prying up the clip holding the cover
on the cartridge.
3. Using a knife remove the large silver seal.
4. Underneath the large silver seal there are two holes (filling hole and vent hole), use the
eyelet screw to widen the hole closest to the center of the cartridge (not the hole closest
to the edge of the cartridge).
5. Connect the needle to the syringe and fill ink.
6. Insert the syringe into the hole that was located under the large silver seal. Note: You
may feel a slight pressure because the cartridge contains a sponge.
7. Inject about 7 ml. of ink and seal the filling hole and vent hole with a piece of tape.
8. Snap the plastic cover back onto the cartridge the same direction it came off.
9. Rinse the syringe with water and dry between each color refill or store for future use.
10. Remove the tape covering the bottom hole and reinsert the cartridge(s) and run a
priming cycle as per printer instructions.
Note: Immediately refill any empty cartridge
LC41C, LC41M, LC41Y, LC41BK
1. Stand the cartridge on a towel or ink spillable table. Using the eyelet screw provided,
begin twisting the screw into the front of the cartridge (see illustration to the right).
Continue twisting until it pierces the plastic..
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe into the hole and inject about 20 ml. of ink
4. Seal the filling hole with one of the included tape dots or a piece of duct tape.
5. Rinse the syringe with water and dry between each color refill or store for future use.
LC25Bk, LC25C, LC25M, LC25Y
1. Use the eyelet screw to remove the white plug located next to the exit hole. The plug
does not need to be removed completely since the white plug and the exit hole plug are
connected.
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole which is found where the white plug was
removed.
4. Inject up to 8 ml. of ink (this cartridge is transparent so you will see the ink level) then
reseal the cartridge with the plug that was removed from step 1. Make sure that the
small plastic tip of the plug sits back into the filling hole.
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridge
LC51
1. Cut the label at joint between the top and bottom halves of the cartridge case.
2. Flip open the cartridge casing (shell).
3. Remove the cartridge from the casing (shell).
4. There is a round hole (well) in the top of the cartridge. Inside the hole or well is
a rubber stopper. Use a thumb drill and drill through the rubber stopper.
Note: Do not bump or press the “pressure release button”.
5. Attach the needle onto the syringe and fill the syringe with 10 ml of ink.
6. Insert the needle through the drilled stopper hole and into the cartridge body.
Please be sure the needle does not press up against the bag or puncture it, as this
will ruin the cartridge and make it unusable.
7. Very slowly inject the 10 ml of ink into the cartridge bag. If ink starts to come
out of the filling hole, stop, as the cartridge is now full (pull back 1 ml of ink
from the cartridge back into the syringe to insure that the cartridge is not overfilled).
Unused ink can be returned to the bottle.
8. Remove the syringe with needle from the cartridge and seal the hole using the
green tape dots provided or electrical tape. Make sure the hole is sealed airtight.
9. Place the cartridge back into its casing (shell) and use a piece of tape to hold the
two sides of the casing (shell) together.
10. Re-install the cartridge back into the printer and run 1 to 3 cleaning cycles as
per printer instructions.
LC61C, LC61M, LC61Y, LC61BK,
LC65BK, LC65C, LC65Y, LC65M
1. Stand the cartridge on a towel or ink spillable table. Using the eyelet
screw provided, begin twisting the screw into the front of the cartridge
(see illustration to the right). Continue twisting until it pierces
the plastic..
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe into the hole and inject about 20 ml. (Or until the
cartridge is full but not overfilled ) of ink.
4. Seal the filling hole with one of the silicon plugs included. You will
need to make adjustments to the plug so that nothing stands out or
bulges out once its inserted.
5. After you have made the necessary adjustments, use a small piece of
duct tape or electrical tape to help hold down the silicon plug. You
will want to make sure this area is flat to the surrounding surface. You
can also use a small allen screw to plug the hole if needed. (This is
very important since this is part of the area that will slide into the
cartridge slot in the printer. If this area bulges out to far, it can pull
off the area you just sealed and cause the cartridge to leak)
6. Your cartridge has now been refilled and is ready for use.
7. Rinse the syringe with water and dry between each color refill or
store for future use.
LC71C, LC71M, LC71Y, LC71BK
1. Stand the cartridge on a towel or ink spillable table. Using the eyelet
screw provided, begin twisting the screw into the front of the cartridge
(see illustration to the right). Continue twisting until it pierces
the plastic..
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe into the hole and inject about 20 ml. (Or until the
cartridge is full but not overfilled ) of ink.
4. Seal the filling hole with one of the silicon plugs included. You will
need to make adjustments to the plug so that nothing stands out or
bulges out once its inserted.
5. After you have made the necessary adjustments, use a small piece of
duct tape or electrical tape to help hold down the silicon plug. You
will want to make sure this area is flat to the surrounding surface. You
can also use a small allen screw to plug the hole if needed. (This is
very important since this is part of the area that will slide into the
cartridge slot in the printer. If this area bulges out to far, it can pull
off the area you just sealed and cause the cartridge to leak)
6. Your cartridge has now been refilled and is ready for use.
7. Rinse the syringe with water and dry between each color refill or
store for future use
LC75C, LC75M, LC75Y, LC75BK,
LC79BK, LC79C, LC79Y, LC79M
1. Stand the cartridge on a towel or ink spillable table. Using the eyelet
screw provided, begin twisting the screw into the front of the cartridge
(see illustration to the right). Continue twisting until it pierces
the plastic..
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe into the hole and inject about 20 ml. (Or until the
cartridge is full but not overfilled ) of ink.
4. Seal the filling hole with one of the silicon plugs included. You will
need to make adjustments to the plug so that nothing stands out or
bulges out once its inserted.
5. After you have made the necessary adjustments, use a small piece of
duct tape or electrical tape to help hold down the silicon plug. You
will want to make sure this area is flat to the surrounding surface. You
can also use a small allen screw to plug the hole if needed. (This is
very important since this is part of the area that will slide into the
cartridge slot in the printer. If this area bulges out to far, it can pull
off the area you just sealed and cause the cartridge to leak)
6. Your cartridge has now been refilled and is ready for use.
7. Rinse the syringe with water and dry between each color refill or
store for future use.
2 komentar:
I am really very agree with your qualities it is very helpful for look like home. Thanks so much for info and keep it up.
canon toner cartridges
i print often and thanks to brother's inkjet i am able to save more without compromising the quality of my prints
Posting Komentar